E. Lession-02

01

 

 

Rectifiers:-

 

Power System 2012

Power System 2012
48V/6400A, 1 phase modules 48V/50A,
24V/100A and 3 phase modules 48V/100A
The PS 2012 can house up to 64 hot-plugged rectifiers, an LVD device, AC and DC distribution panels, optional DC/AC inverters and DC/DC converters — all managed and controlled by a sophisticated system controller, the SC 2012 NET.

 

Features
Up to 64 parallel hot-plugged rectifiers.
One- or three-phase input configuration.
Low voltage disconnect device (LVD) for battery protection (option for 2 LVDs)
High-performance system controller, SC 2012 NET, used to measure, monitor, and control voltages, currents,
temperature, battery parameters, and other data.

Temperature compensation for extended battery life
Up to two battery sets handled in one system.
Automatic and pre-programmed battery test algorithm
Automatic and pre-programmed equalize charging mode
AC and DC distribution panels, flexible in accommodating user requirements.
Intelligent digital active current sharing among rectifiers
Flexible user-defined signaling of dry contacts
Comprehensive remote control and monitoring software: GeMSi
RS232 and/or TCP/IP communication
System Controller 2012 NET
24 user-definable digital inputs
22 user-definable digital outputs
Four galvanic-isolated 10-bit resolution voltmeters
Up to four 10-bit resolution ampere meters
24 indicator LEDs on the front panel
Control of up to 64 rectifiers
Control of up to 20 additional DC/DC converters
Large 4×40 character LCD with back light
Numeric keypad on panel
Control of LVD(s)
Periodic or manual battery check
DC voltage compensation according to battery temperature
Three temperature sensors for reliable measurement
Audible alarm
Calibration by software (all-digital, no analog potentiometers) of AC and DC currents and voltages measured by the controller
Real-Time-Clock (RTC) with backup
256 events log and data log (statistic values)
Graphic user interface (GUI)
RS232 and / or SNMP (PPP-10BASET) and TCP/IP communication
Measurements and Indications
DC voltage
Load current
Battery current(s)
Rectifiers currents
AC voltage(s), current(s), and frequency
Status of input, output, LVD, rectifiers, battery, system breakers
Battery temperature
Dry-contact signalization, user-definable (14 alarms)
Control
Battery test
DC voltage setting (EQUALIZE or FLOAT charge modes)
LVD threshold setting (connect, disconnect)
Rectifier activation/shutdown (up to 48 rectifiers in one power system)

 

 

 

48VDC/180A plug in shelf / Options for 12V, 24V, 60V, 110V voltages 
PS 1006 provides clean DC power to sensitive equipment, and at the same time charges the battery bank

and supplies power during mains failure. PS 1006 contains a 19” subrack that can house up to
6 hot-plugged rectifiers, a V/A meter or controller, and an LVD device.
PS 1006 is available in two configurations, with a V/A meter or with the System Controller 1006.
An optional 1006 NET controller offers SNMP over TCP/IP communication and user-defined
RS232 or SNMP communication.

 

Enatel-110V-DC-Power-Systems

Features
Up to 6 hot-plugged rectifiers
Universal input voltage
Active current sharing
Built-in dual 70A electronic low voltage disconnect device (ELVD) for battery protection
High-performance, hot-plugged system controller (SC 1006) used to measure, monitor, and control AC and DC voltages, currents (load, battery, rectifiers), power, temperature, battery parameters, and additional data
Temperature compensation for extended battery life
Up to two battery sets handled in one system
Automatic and pre-programmed battery test for each battery set
Automatic and pre-programmed equalize charging mode
Battery/load terminals protected by a dedicated thermal-magnetic circuit breaker
RS232 (SC 1006) or TCP/IP (SC 1006 NET) communication
System Controller SC 1006 (Standard)
Large, bright three-digit display
Control of e-LVD(s)
Periodic or manual battery check
DC voltage compensation according to battery temperature
Two temperature sensors for reliable measurement
Indicator LEDs on the front panel
Audible alarm
Calibration by software (all-digital, no analog potentiometers)
Graphic user interface (GUI)
Real-time-clock (RTC) with backup
Event log
RS232 serial port
Measurements and Indications
DC voltage
Load current
Battery current
Rectifiers current
Power (in Watts)
AC voltage and frequency
Status of input, output, e-LVD, rectifiers, battery, system breakers
Battery temperature
Breaking alert by modem
Dry-contact signals (three alarms)
Control
Battery test
Two charging modes (FL, EQ)
DC voltage setting (EQUALIZE or FLOAT charge modes)
ELVD threshold setting (connect, disconnect)
Unconditional control of each ELVD
System Controller 1006 NET (optional)
In addition to the standard features, the NET model offers:
SNMP – TCP/IP communication
User defined communication: RS232 or SNMP (PPP / 10baseT)

 

 

 

Push-to-Reset Thermal Circuit Breaker

 

Series_17_Banner_11

Compact Design, Single Pole

Trip-free Cycling, Economically Priced

MP Series 12

trionobackground

Available in ratings from 3 to 20 Amperes, the NEW Series 12 offers a very economical, compact design in single pole circuit protection.  The Series 12 Thermal Circuit Breakers have a rated voltage of 125/250VAC, 50VDC with an Interrupt Capacity of 1000A and a Dielectric Strength of 1500VAC.  All are ROHS Compliant and UL1077 approved, with many amp ratings having CSA, CCC, and VDE/IEC approvals as well.

The MP Series 12 is designed for various applications in Household Appliances, Power Strips, Audio Visual Equipment, Marine Panels, Transportation, and more. They are available in various threaded and snap-in bushings, along with multiple Quick Connect terminal variations.  Economically priced, these Series 12 thermal circuit breakers are the choice where space and price are vital to the application.

Advertisements